Jump to content

DVB-T

From Wikipedia, the free encyclopedia

The logo of DVB-T

DVB-T, short for Digital Video Broadcasting – Terrestrial, is the DVB European-based consortium standard for the broadcast transmission of digital terrestrial television that was first published in 1997[1] and first broadcast in Singapore in February 1998.[2][3][4][5][6][7][8] This system transmits compressed digital audio, digital video and other data in an MPEG transport stream, using coded orthogonal frequency-division multiplexing (COFDM or OFDM) modulation. It is also the format widely used worldwide (including North America) for Electronic News Gathering for transmission of video and audio from a mobile newsgathering vehicle to a central receive point. It is also used in the US by Amateur television operators.

Basics

[edit]

Rather than carrying one data carrier on a single radio frequency (RF) channel, COFDM works by splitting the digital data stream into a large number of slower digital streams, each of which digitally modulates a set of closely spaced adjacent sub-carrier frequencies. In the case of DVB-T, there are two choices for the number of carriers known as 2K-mode or 8K-mode. These are actually 1,705 or 6,817 sub-carriers that are approximately 4 kHz or 1 kHz apart.

DVB-T offers three different modulation schemes (QPSK, 16QAM, 64QAM).

DVB-T has been adopted or proposed for digital television broadcasting by many countries (see map), using mainly VHF 7 MHz and UHF 8 MHz channels whereas Taiwan, Colombia, Panama and Trinidad and Tobago use 6 MHz channels. Examples include the UK's Freeview.

The DVB-T Standard is published as EN 300 744, Framing structure, channel coding and modulation for digital terrestrial television. This is available from the ETSI website, as is ETSI TS 101 154, Specification for the use of Video and Audio Coding in Broadcasting Applications based on the MPEG-2 Transport Stream, which gives details of the DVB use of source coding methods for MPEG-2 and, more recently, H.264/MPEG-4 AVC as well as audio encoding systems. Many countries that have adopted DVB-T have published standards for their implementation. These include the D-book in the UK, the Italian DGTVi,[9] the ETSI E-Book and the Nordic countries and Ireland NorDig.

DVB-T has been further developed into newer standards such as DVB-H (Handheld), which was a commercial failure and is no longer in operation, and DVB-T2, which was initially finalised in August 2011.

DVB-T as a digital transmission delivers data in a series of discrete blocks at the symbol rate. DVB-T is a COFDM transmission technique which includes the use of a Guard Interval. It allows the receiver to cope with strong multipath situations. Within a geographical area, DVB-T also allows single-frequency network (SFN) operation, where two or more transmitters carrying the same data operate on the same frequency. In such cases the signals from each transmitter in the SFN needs to be accurately time-aligned, which is done by sync information in the stream and timing at each transmitter referenced to GPS.

The length of the Guard Interval can be chosen. It is a trade-off between data rate and SFN capability. The longer the guard interval the larger is the potential SFN area without creating intersymbol interference (ISI). It is possible to operate SFNs which do not fulfill the guard interval condition if the self-interference is properly planned and monitored.

Technical description of a DVB-T transmitter

[edit]
Scheme of a DVB-T transmission system

With reference to the figure, a short description of the signal processing blocks follows.

  • Source coding and MPEG-2 multiplexing (MUX): Compressed video, compressed audio, and data streams are multiplexed into MPEG program streams (MPEG-PSs). One or more MPEG-PSs are joined together into an MPEG transport stream (MPEG-TS); this is the basic digital stream which is being transmitted and received by TV sets or home Set Top Boxes (STB). Allowed bit rates for the transported data depend on a number of coding and modulation parameters: it can range from about 5 to about 32 Mbit/s (see the bottom figure for a complete listing).
  • Splitter: Two different MPEG-TSs can be transmitted at the same time, using a technique called Hierarchical Transmission. It may be used to transmit, for example a standard definition SDTV signal and a high definition HDTV signal on the same carrier. Generally, the SDTV signal is more robust than the HDTV one. At the receiver, depending on the quality of the received signal, the STB may be able to decode the HDTV stream or, if signal strength lacks, it can switch to the SDTV one (in this way, all receivers that are in proximity of the transmission site can lock the HDTV signal, whereas all the other ones, even the farthest, may still be able to receive and decode an SDTV signal).
  • MUX adaptation and energy dispersal: The MPEG-TS is identified as a sequence of data packets, of fixed length (188 bytes). With a technique called energy dispersal, the byte sequence is decorrelated.
  • External encoder: A first level of error correction is applied to the transmitted data, using a non-binary block code, a Reed–Solomon RS (204, 188) code, allowing the correction of up to a maximum of 8 wrong bytes for each 188-byte packet.
  • External interleaver: Convolutional interleaving is used to rearrange the transmitted data sequence, in such a way that it becomes more rugged to long sequences of errors.
  • Internal encoder: A second level of error correction is given by a punctured convolutional code, which is often denoted in STBs menus as FEC (Forward error correction). There are five valid coding rates: 1/2, 2/3, 3/4, 5/6, and 7/8.
  • Internal interleaver: Data sequence is rearranged again, aiming to reduce the influence of burst errors. This time, a block interleaving technique is adopted, with a pseudo-random assignment scheme (this is really done by two separate interleaving processes, one operating on bits and another one operating on groups of bits).
  • Mapper: The digital bit sequence is mapped into a base band modulated sequence of complex symbols. There are three valid modulation schemes: QPSK, 16-QAM, 64-QAM.
  • Frame adaptation: the complex symbols are grouped in blocks of constant length (1512, 3024, or 6048 symbols per block). A frame is generated, 68 blocks long, and a superframe is built by 4 frames.
  • Pilot and TPS signals: In order to simplify the reception of the signal being transmitted on the terrestrial radio channel, additional signals are inserted in each block. Pilot signals are used during the synchronization and equalization phase, while TPS signals (Transmission Parameters Signalling) send the parameters of the transmitted signal and to unequivocally identify the transmission cell. The receiver must be able to synchronize, equalize, and decode the signal to gain access to the information held by the TPS pilots. Thus, the receiver must know this information beforehand, and the TPS data is only used in special cases, such as changes in the parameters, resynchronizations, etc.
Spectrum of a DVB-T signal in 8k mode (note the flat-top characteristics)
  • OFDM modulation: The sequence of blocks is modulated according to the OFDM technique, using 1705 or 6817 carriers (2k or 8k mode, respectively). Increasing the number of carriers does not modify the payload bit rate, which remains constant.
  • Guard interval insertion: to decrease receiver complexity, every OFDM block is extended, copying in front of it its own end (cyclic prefix). The width of such guard interval can be 1/32, 1/16, 1/8, or 1/4 that of the original block length. Cyclic prefix is required to operate single frequency networks, where there may exist an ineliminable interference coming from several sites transmitting the same program on the same carrier frequency.
  • DAC and front-end: The digital signal is transformed into an analogue signal, with a digital-to-analog converter (DAC), and then modulated to radio frequency (VHF, UHF) by the RF front end. The occupied bandwidth is designed to accommodate each single DVB-T signal into 5, 6, 7, or 8 MHz wide channels. The base band sample rate provided at the DAC input depends on the channel bandwidth: it is samples/s, where is the channel bandwidth expressed in Hz.
Available bit rates (Mbit/s) for a DVB-T system in 8 MHz channels
Modulation Coding rate Guard interval
1/4 1/8 1/16 1/32
QPSK 1/2 4.976 5.529 5.855 6.032
2/3 6.635 7.373 7.806 8.043
3/4 7.465 8.294 8.782 9.048
5/6 8.294 9.216 9.758 10.053
7/8 8.709 9.676 10.246 10.556
16-QAM 1/2 9.953 11.059 11.709 12.064
2/3 13.271 14.745 15.612 16.086
3/4 14.929 16.588 17.564 18.096
5/6 16.588 18.431 19.516 20.107
7/8 17.418 19.353 20.491 21.112
64-QAM 1/2 14.929 16.588 17.564 18.096
2/3 19.906 22.118 23.419 24.128
3/4 22.394 24.882 26.346 27.144
5/6 24.882 27.647 29.273 30.160
7/8 26.126 29.029 30.737 31.668

Technical description of the receiver

[edit]

The receiving STB adopts techniques which are dual to those ones used in the transmission.

  • Front-end and ADC: the analogue RF signal is converted to base-band and transformed into a digital signal, using an analogue-to-digital converter (ADC).
  • Time and frequency synchronization: the digital base band signal is searched to identify the beginning of frames and blocks. Any problems with the frequency of the components of the signal are corrected, too. The property that the guard interval at the end of the symbol is placed also at the beginning is exploited to find the beginning of a new OFDM symbol. On the other hand, continual pilots (whose value and position is determined in the standard and thus known by the receiver) determine the frequency offset suffered by the signal. This frequency offset might have been caused by Doppler effect, inaccuracies in either the transmitter or receiver clock, and so on. Generally, synchronization is done in two steps, either before or after the FFT, in such way to resolve both coarse and fine frequency/timing errors. Pre-FFT steps involve the use of sliding correlation on the received time signal, whereas Post-FFT steps use correlation between the frequency signal and the pilot carriers sequence.
  • Guard interval disposal: the cyclic prefix is removed.
  • OFDM demodulation: this is achieved with an FFT.
  • Frequency equalization: the pilot signals are used to estimate the Channel Transfer Function (CTF) every three subcarriers. The CTF is derived in the remaining subcarriers via interpolation. The CTF is then used to equalize the received data in each subcarrier, generally using a Zero-Forcing method (multiplication by CTF inverse). The CTF is also used to weigh the reliability of the demapped data when they are provided to the Viterbi decoder.
  • Demapping: since there are Gray-encoded QAM constellations, demapping is done in a "soft" way using nonlinear laws that demap each bit in the received symbol to a more or less reliable fuzzy value between -1 and +1.
  • Internal deinterleaving
  • Internal decoding: uses the Viterbi algorithm, with a traceback length larger than that generally used for the basic 1/2 rate code, due to the presence of punctured ("erased") bits.
  • External deinterleaving
  • External decoding
  • MUX adaptation
  • MPEG-2 demultiplexing and source decoding

Countries and territories using DVB-T or DVB-T2

[edit]
Digital terrestrial television systems worldwide. Countries using DVB-T or DVB-T2 are shown in blue.[10]

Americas

[edit]

Europe

[edit]

Oceania

[edit]

Asia

[edit]

Africa

[edit]

Countries and territories are available in DVB-T

[edit]

Americas

[edit]

Europe

[edit]

Oceania

[edit]

Asia

[edit]

Africa

[edit]

DVB-T/T2 switch-off

[edit]

DVB-T/T2 is switched off in Switzerland and the Flemish part of Belgium. The EU plans to switch off DVB-T/T2 in its member states by 2030.[citation needed]

  • Belgium: In Flanders, VRT free-to-air broadcasting ended on 1 December 2018. In Flanders region, the encrypted TV platform TV Vlaanderen's Antenne TV service will be end on 1 September 2024.[needs update]
  • Switzerland: Swiss public broadcaster SRG SSR terminated DTT network on 3 June 2019. A regional station from the Geneva area has kept broadcasting. A DVB-T2 antenna was later activated in the east of the country to relay Swiss TV to Austrian cable operators. A similar broadcast is planned to cover Grand Geneva.

See also

[edit]

Notes

[edit]
  1. ^ "ETSI EN 300 744 – Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television" (PDF). European Telecommunications Standards Institute. October 2015. p. 66. Archived (PDF) from the original on 26 March 2016.
  2. ^ "DATAONE LIMITED RESPONSE TO CONSULTATION PAPER ON DATACASTING" (PDF). Infocomm Media Development Authority, Singapore. Archived (PDF) from the original on 5 February 2020.
  3. ^ "TELEVISION BROADCAST FOR SINGAPORE – March 3, 1998" (PDF). 8 October 1999. Archived (PDF) from the original on 8 October 1999. Retrieved 5 February 2020.
  4. ^ "Advent Television launches the world's first digital terrestrial service in Singapore" (PDF). 8 October 1999. Archived (PDF) from the original on 8 October 1999. Retrieved 5 February 2020.
  5. ^ "The Future is in Digital Broadcasting and that future is with Advent Television". 11 April 2001. Archived from the original on 11 April 2001. Retrieved 5 February 2020.
  6. ^ "Press Release – April 27, 1998" (PDF). 4 June 2000. Archived (PDF) from the original on 4 June 2000. Retrieved 5 February 2020.
  7. ^ "S'pore testing digital TV format". The Business Times. 5 March 1998. p. 4.
  8. ^ "SBA plans to launch digital TV after trying out systems". The Straits Times. 9 March 1998. p. 30.
  9. ^ "DGTVi – Per la Televisione Digitale Terrestre" (in Italian). Archived from the original on 2008-04-19. Retrieved 2008-07-30.{{cite web}}: CS1 maint: unfit URL (link)
  10. ^ DVB.org Archived 20 March 2011 at the Wayback Machine, Official information taken from the DVB website
  11. ^ "Colombia adopta el estándar europeo para la tv digital terrestre". El Espectador (in Spanish). 28 August 2008. Archived from the original on 13 April 2019. Retrieved 28 August 2008.
  12. ^ "TV Digital no ha llegado a toda Colombia y la CNTV ya piensa en modificar la norma". Evaluamos (in Spanish). 21 July 2011.
  13. ^ "Panama adopts DVB-T". DVB.org. 19 May 2009. Archived from the original on 3 September 2013. Retrieved 26 June 2016.
  14. ^ "KTV Ltd". Retrieved 26 June 2016.
  15. ^ "Plan for the introduction of terrestrial digital television broadcasting (DVB-T) in the Republic of Bulgaria" (in Bulgarian). Ministry of Transport, Information Technology and Communications of Bulgaria. Retrieved 17 December 2012.
  16. ^ "Digital Television". NURTS (TV tower operator). Archived from the original on 1 December 2012. Retrieved 17 December 2012.
  17. ^ "Digital Ísland" (in Icelandic). fjarskiptahandbokin.is. Archived from the original on 31 August 2009. Retrieved 27 October 2009.
  18. ^ "Russia adopts DVB-T2". Advanced-Television.com. 29 September 2011.
  19. ^ "ETV: trial DVB-T2 network" (in Serbian). Archived from the original on 16 April 2012. Retrieved 22 March 2012.
  20. ^ "Switzerland to switch off DTT on June 3, 2019". 6 December 2018.
  21. ^ "TRT Kurumsal Profil - TRT Kurumsal".
  22. ^ "RTÜK | Sayısal Yayıncılık Nedir?".
  23. ^ [1]
  24. ^ "100,000 likes – Oqaab reaches over 1 Mio TV Households". Oqaab.af. 31 March 2015. Archived from the original on 23 March 2016. Retrieved 26 June 2016.
  25. ^ a b c d e f g h Hawkes, Rebecca (19 May 2014). "Samart eyes Middle East market for digital TV-enabled smartphone". Rapid TV News. Retrieved 26 June 2016.
  26. ^ "Digital TV services to be introduced in Bangladesh by 2014". Asia-Pacific Broadcasting Union. 5 June 2012.
  27. ^ "PERSYARATAN TEKNIS ALAT DAN PERANGKAT PENERIMA TELEVISI SIARAN DIGITAL BERBASIS STANDAR DIGITAL VIDEO BROADCASTING TERRESTRIAL – SECOND GENERATION" (PDF). KomInfo.go.id. Ministry of Communication and Information Technology (Indonesia). Archived (PDF) from the original on 31 March 2014. Retrieved 1 April 2017.
  28. ^ "Standar Penyiaran Televisi Digital" (PDF). KomInfo.go.id. Ministry of Communication and Information Technology (Indonesia). Archived from the original (PDF) on 27 June 2017. Retrieved 19 February 2012.
  29. ^ Hawkes, Rebecca (26 February 2014). "Kuwait TV opts for Harris DVB-T2 technology". Rapid TV News. Retrieved 11 April 2014.
  30. ^ "Kyrgyztelecom launches DVB-T2 & DVB-S2". DVB.org. 7 November 2014. Archived from the original on 19 April 2016. Retrieved 7 April 2016.
  31. ^ "北朝鮮で4局が地上デジタル放送を実施中、ASUS ZenFone Go TVで確認". blogofmobile.com (in Japanese). 8 September 2019. Retrieved 24 June 2020.
  32. ^ Williams, Martyn (17 March 2013). "Report: DPRK testing digital TV". North Korea Tech – 노스코리아테크. Archived from the original on 23 September 2019. Retrieved 25 September 2019.
  33. ^ "Qatar Goes DVB-T2". DVB.org. 11 December 2013. Archived from the original on 26 September 2019. Retrieved 12 April 2014.
  34. ^ "Tajikistan Confirms DVB-T2 Adoption". DVB.org. 4 February 2014. Archived from the original on 29 December 2016. Retrieved 7 April 2016.
  35. ^ Mochiko, Thabiso (26 November 2010). "BusinessDay – State U-turn on Nyanda's digital-TV signal plan". BusinessDay.co.za. BDFM Publishers. Archived from the original on 30 November 2010. Retrieved 26 November 2010.
  36. ^ Etherington-Smith, James (3 January 2011). "DVB-T2 chosen as digital TV standard". MyBroadband.co.za. Retrieved 3 January 2011.

References

[edit]
  • ETSI Standard: EN 300 744 V1.5.1, Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television, available at ETSI Publications Download Area (This will open ETSI document search engine, to find the latest version of the document enter a search string; free registration is required to download PDF.)
[edit]